Share your VPN Experience
Cisco has made changes for the Security exams by replacing the old CCSP with the new CCNP Security Certification with 4 modules: Secure, Firewall, IPS and VPN. In fact, the old CCSP and the new CCNP Security are very similar. Many candidates have requested us to put up materials for these new exams but it is a time-consuming work. In the mean time, we created the “Share your experience” for the VPN exam. We really hope anyone who read securitytut, 9tut, digitaltut, certprepare, networktut and voicetut contribute to these sections as your experience is invaluable for CCNP Security learners to complete their goals.
Please share with us your experience after taking the VPN 642-647 exam, your materials, the way you learned, your recommendations…
Can someone explain how to verify the bookmarks lab? Looks like I also got the same error as Brad when I did my exam and eventually failed by a close margin.
Anyone remember what were the new DMVPN D&D questiona steps?
What are two benefits of using IKEv2 instead of IKEv1 when deploying remote-access IPsec VPNs? (Choose two.)
A. IKEv2 supports EAP authentication methods as part of the protocol.
B. IKEv2 inherently supports NAT traversal.
C. IKEv2 messages use random message IDs.
D. The IKEv2 SA plus the IPsec SA can be established in six messages instead of nine messages.
E. All IKEv2 messages are encryption-protected.
Someone know?
I´ll ask again, now I can also offer a supermariov4 vce file running properly.
Anyone has something for 300-209 more narrow and valid than supermarioV4? Can offer exchange for any of the rest (300-206,300-208,300-210, and a supermariov4 vce file running properly).
Someone say something more about new DMVPN D&D ??
@Wild_Wolf do you remember the 8 steps for D&D?
Does anyone have the new 8 D&D for the DMVPN?
Guys, i failed…..there is completely new question set….with only about 30% overlap….the Clientless SSL VPN lab also doesnt work even after doing the steps from supermario the SSL VPN portal doesnt show the bookmarks…..
@Anonymous : thanks for the file
the SSL Bookmark just worked fine for me. Just make sure you logout after you login to the SSL VPN as per 1st step. if you don’t logout then whatever the changes you have made to the bookmarks wouldn’t reflect on the SSL vpn and even though the question said that configurations will be automatically saved to the devices, the good practice is to save the config using apply button.
@newcomer: Below are the complete process just remember in the order and you will be just fine in the exam
1. When the Tunnel on the Spoke is “no shutdown” it generates a NHRP Registration Request, which starts the DMVPN process. As the Hub’s configuration is completely dynamic, the Spoke must be the endpoint which initiates the connection.
2. The NHRP Registration Request is then encapsulated in GRE which triggers the crypto process to start.
3. At this point, the first ISAKMP Main Mode message – ISAKMP MM1 – is sent from the Spoke to the Hub on port UDP500.
4. The Hub receives and processes MM1 and responds with ISAKMP MM2, as it has a matching ISAKMP policy.
5. Once the Spoke receives the MM2, it responds with MM3. As with MM1, the Spoke confirms the received ISAKMP policy is valid.
6. The Hub receives MM3 and responds with MM4.
7. At this point in the ISAKMP negotiation, the Spoke might respond on port UDP4500 if NAT is detected in the transit path. However, if no NAT is detected the Spoke continues and sends MM5 on UDP500. Lastly, the Hub responds with MM6 in order to complete the Main Mode exchange.
8. Once the Spoke receives MM6 from the Hub, it sends QM1 to the Hub on UDP500 in order to begin Quick Mode.
9. The Hub receives QM1 and responds with QM2, as all received attributes are accepted. At this point the Hub creates the Phase 2 SAs for this session.
10. As the last step of the Quick Mode negotiation, QM2 is received by the Spoke. The Spoke then creates its Phase 2 SAs and sends QM3 in response. This completes the ISAKMP and IPSec negotiation. There is now an IPSec session which encrypts GRE traffic between these two peers.
11. Now that the crypto session is up and able to pass traffic, these packets are encapsulated within the GRE over IPSec tunnel
@Wild Wolf
Did you use the wizard for ssl or it is not available and you need to use the other way?
What are two benefits of using IKEv2 instead of IKEv1 when deploying remote-access IPsec VPNs? (Choose two.)
A. IKEv2 supports EAP authentiedcation methods as part of the protocol.
B. IKEv2 inherently supports NAT traversal.
C. IKEv2 messages use random message IDs.
D. The IKEv2 SA plus the IPsec SA can be established in six messages instead of nine messages.
E. All IKEv2 messages are encryption-protected.
Someone know?
@Dnny it’s a shame. You have to try again.
But Danny, you only had 76 questions. While the proper dump has less than half a thousand questions that you need to learn, plus forum and knowledge.
@Anonymous
A. IKEv2 supports EAP authentiedcation methods as part of the protocol.
@Danny, I have gotta say 30% is not a bad percentage for 76 questions.
I’m looking for a 300-209 dump, an accurate one . not 400Q,
I will join a group buys’ or pay for it.
@trt1234 I wish I have dump to share with mate, I still have 209 and 208 is pending.
To be sure, please confirm if the lab below is the one that is on the exam?
htt: *//w*ww.examtopics.com/*discussions/cisco/*view/8510-exam-300-209-topic-1-question-133-discussion/
SIMULATION –
Scenario:
You are the network security manager for your organization. Your manager has received a request to allow an external user to access to your HQ and DM2 servers. You are given the following connection parameters for this task.
Using ASDM on the ASA, configure the parameters below and test your configuration by accessing the Guest PC. Not all AS DM screens are active for this exercise. Also, for this exercise, all changes are automatically applied to the ASA and you will not have to click APPLY to apply the changes manually.
Enable Clientless SSL VPN on the outside interface
Using the Guest PC, open an Internet Explorer window and test and verify the basic connection to the SSL VPN portal using address: htt ps *//v pn-s ecu re- x.public
a. You may notice a certificate error in the status bar, this can be ignored for this exercise
b. Username: vpnuser
c. Password: cisco123
d. Logout of the portal once you have verified connectivity
Configure two bookmarks with the following parameters:
a. Bookmark List Name: MY-BOOKMARKS
b. Use the: URL with GET or POST method
c. Bookmark Title: HQ-Server
i. htt :* // 10 .10.3.20
d. Bookmark Title: DMZ-Server-FTP
i. ft p *//172. 16.1.50
e. Assign the configured Bookmarks to:
i. DfltGrpPolicy
ii. DfltAccessPolicy
iii. LOCAL User: vpnuser
From the Guest PC, reconnect to the SSL VPN Portal
Test both configured Bookmarks to ensure desired connectivity
You have completed this exercise when you have configured and successfully tested Clientless SSL VPN connectivity.
Topology:
Guys,
For the simulation, i noticed the solution in the dumps filled http for both bookmarks instead of 1http and 1ftp on asdm. Does this matter?
@Dymos yes it is the same. @Fido it should be one HTTP and one FTTP. bu for few they were not able to check the bookmarks after logging back . Even though they log out and did all in the adsm and also clikced the apply button and then logged back from guest PC and not able to find test the bookmarks ??
Can anyone suggest why many were not able to test the SSL lab bookmarks please ?? even after configuring the bookmarks and clicked the apply button.
@Brad: I used ASDM, which worked fine for me. Just a thought if someone missing the trick, you need to assign the configured Bookmarks to DfltGrpPolicy, DfltAccessPolicy and vpnuser in order to reflect the change in the Guest PC
@Dymos3: Yes thats the same Lab in the exam.
@Brad, Please refer the below URL, in the PDF format its the Question 156, it has the detailed steps but for DMZ-Server-FTP use FTP protocol from the drop down menu as in the pdf file it has mentioned as http. rest is the same… Good luck
od.lk/fl/MThfMTE2NTQ4NF8
Are there any configured labs that we use to practise for the 209 exam
@Brad
Would you share your feedback when you take the exam again please ?
I should take the exam in the next few days , Super Mario, new 7 questions , new DMVPN D&D
any other things have changed ?
Guys, you are right i had purchased dumps and in the past they have been pretty accurate but not so much this time……..also i did everything mentioned in the solution for the Clientless SSL VPN lab but the bookmarks did not show up even after hitting apply and logging in and out…….also what i noticed was even before enabling the vpn on the outside interface the htt ps *//v pn-s ecu re- x.public is accessible from the guest pc……i think something has definitely changed in the lab since the new question set was rolled out so even though the question has not changed the same solution is not giving the same results….
someone has valid dumps for 300-210??
@Danny maybe there was something turned on that blocked websites
You tried it ?
ASA(config)# dynamic-access-policy-record DfltAccessPolicy
ASA(config-dynamic-access-policy-record)# webvpn
ASA(config-dap-webvpn)# no url-list none
ASA#show run dynamic-access-policy-record
@Danny You haven’t seen any bookmarks? Empty? Describe more, pls.
As for me it is one of two:
1) the lab is faulty
2) there are changes in the lab that block display bookmarks. This can only be set in DAP (ASDM).
Configuration > Remote Access VPN > Clientless SSL VPN Access > Dynamic Access Policies
tab bookmarks
Or set in CLI, as I wrote earlier post.
What do felles think about it? I am asking for your opinion ???
How do you think anyone from cisco is watching this forum ?
Which three remote access VPN methods in an ASA appliance provide support for Cisco Secure Desktop? (Choose three.)
A.IKEv1
B.IKEv2
C.SSL client
D.SSL clientless
E.ESP
F.L2TP
Is IKEv2 correct? I couldnt find any references
Hi did anyone took the exam is the supermario still valid can you please share your experience
Hello,
I passed SIMOS last week. Here’s what I used for study:
– 8 years of security experience with ASA…helped a lot
– CBT Nuggets (SIMOS + VPN, this is important)
– VPN Cisco book (must have)
– I checked Mario’s file. I felt like there was a lot of errors in it. DMVPN stages was good though. I also had the bookmark lab. Seriously guys, the lab have most of the option grayed out. You just can’t get wrong otherwise you seriously need to practice.
Good luck to all
I passed today here are few tips.
1. Please don’t panic
2. Supermario still enough to make you pass
3. With regarding to the lab mine worked just make sure you logout before making any changes on the Asdm.
4. DMVPN eight steps if you go through Wild_Wolf steps then you should be alright..
@Passed Today
Congrats!!!
You’re saying once you are complete with the lab, logout and you should be good to check on the PCs?
Also, DMVPN D&D absolutely changed?
Authorization of a clientless SSL VPN defines the actions that a user may perform within a
clientless SSL VPN session. Which statement is correct concerning the SSL VPN authorization
process?
A.
Remote clients can be authorized by applying a dynamic access policy, which is configured on an
external AAA server.
B.
Remote clients can be authorized externally by applying group parameters from an external database.
C.
Remote client authorization is supported by RADIUS and TACACS+ protocols.
D.
To configure external authorization, you must configure the Cisco ASA for cut-through proxy.
Answer mentioned is B but I assume it could be C? Any thoughts
Hello
I passed today.
Supermario dump is still valid !!
And allows to pass a good result.
There are only 2-3 new questions that are not here (in the forum) or in the supermario dumps.
Lab has not changed. The ASDM lab is fine and working properly.
There were no problems with my lab.
D&D dmvpn has 8 steps. You must learn all the DMVPN process before the exam.
However, I strong recommended you to learn the material form simos (ipsec,dmvpn,flexvpn,getvpn,remote-access,vpn in IOS and ASA etc..) and goood learn the entire supermario dumps.
For example, I was preparing for the exam for several months (for novemver 2019).
Good luck for all !
ATTENTION PLEASE!
The new PassLeader 300-206 dumps (Updated Recently) now are available, here are part of 300-206 exam questions (FYI):
[Get the download link at the end of this post]
NEW QUESTION 492
Which two device types can you examine with a TrustSec Readiness Assessment report? (Choose two.)
A. SGACL devices
B. TrustSec incapable devices
C. enforcement devices
D. authentication devices
E. security group tagging devices
Answer: BC
NEW QUESTION 493
An engineer has found that threat detection has been turned on by default on a Cisco ASA. Which two security events are monitored? (Choose two.)
A. number of times the rates were exceeded
B. total number of malformed packets received
C. denial of service attack occurrences
D. packets allowed by the inspection engine
E. concurrent NAT interface overload addresses
Answer: AC
NEW QUESTION 494
Which two values must you provide when you use a CSV file to import devices into Cisco Prime Infrastructure? (Choose two.)
A. device model number
B. SNMP version
C. device serial number
D. device IP address
E. EtherType field
Answer: BD
NEW QUESTION 495
Which two features does DNSSEC leverage for proper functionality? (Choose two.)
A. It uses TCP to ensure reliable delivery.
B. It uses UDP to reduce the DNS responses time.
C. It uses EDNS to manage the larger DNS packets it requires.
D. It uses UDP to minimize packet size.
E. It uses AD and DO inside UDP to reduce response time.
Answer: CE
NEW QUESTION 496
Which two unified communications protocols can be inspected for an anomaly by using the Cisco ASA 5500 Series firewall? (Choose two.)
A. RSH
B. SCP
C. MGCP
D. TFTP
E. RTSP
Answer: CE
NEW QUESTION 497
Which purpose of MKA in a MACsec deployment is true?
A. It encrypts traffic between switches.
B. It transports EAP messages from access switches to the RADIUS server.
C. It provides additional security features beyond the default SAP key exchange.
D. It encrypts traffic between the downlink port and the endpoint of the switch.
Answer: D
NEW QUESTION 498
Due to a traffic storm on your network, two interfaces were error-disabled and both interfaces sent SNMP traps. In which two ways can the interfaces be back into service? (Choose two.)
A. If the snmp-server enable traps command is enabled, the ports return to service automatically after 300 seconds.
B. If EEM is configured, the ports return to service automatically in less than 300 seconds.
C. If the administrator enters the shutdown and no shutdown commands on the interfaces.
D. If the interfaces are configured with the error-disable detection and recovery feature, the interfaces will be returned to service automatically.
E. If Cisco Prime is configured, it issues an SNMP set command to re-enable the ports after the preconfigured interval.
Answer: CD
NEW QUESTION 499
You need to increase the level of security for the management traffic accessing a Cisco router. You plan to enable HTTPS. Which action do you take on the router?
A. Disable TCP port 23.
B. Generate an RSA key.
C. Enable SCP.
D. Enable TLS.
Answer: D
NEW QUESTION 500
Which action do you take on a Cisco router to limit the management traffic to only one interface?
A. Filter incoming connections by applying an extended ACL on a loopback interface.
B. Filter incoming connections by applying a standard ACL on a SVI.
C. Utilize the Management Plan Protection feature.
D. Add an interface by using the management-interface command.
Answer: C
NEW QUESTION 501
……
P.S.
PassLeader 300-206 dumps FYI:
od.lk/fl/NjFfMTUyNjc0M18
(501q~~~NEW VERSION DUMPS!!!)
Good Luck!!!
[(copy that link and open it in your web browser!!!)]
By the way:
1. PassLeader 300-208 dumps FYI:
od.lk/fl/NjFfMTUyNjc0NV8
(521q~~~NEW VERSION DUMPS!!!)
~~~~~~~~~~~~~~~~~~~~~~~~~
2. PassLeader 300-209 dumps FYI:
od.lk/fl/NjFfMTUyNjc0N18
(459q~~~NEW VERSION DUMPS!!!)
~~~~~~~~~~~~~~~~~~~~~~~~~
3. PassLeader 300-210 dumps FYI:
od.lk/fl/NjFfMTUyNjc0OV8
(508q~~~NEW VERSION DUMPS!!!)
~~~~~~~~~~~~~~~~~~~~~~~~~
Good Luck!!!
[(copy those links and open them in your web browser!!!)]
Hi all,
any one can confirm the correct 8 steps D&D of dmvpn.
Fast of all thank you guys those who put comments on this forum.
Just pass the exam.
Supermario still valid.
Same SIM(bookmarks) + ikev2 l2l questions ( sh cryp isa key, sh cry isa sa, sh cry ipsec trans )
D&D 8 steps DMVPN and Ikev1 troubleshooting ( attr, qm_idle…etc)
Please read the last 4 or 5 pages of comments on the forum you will be ok.
I used this one
od.lk/f/MThfMTEyMjczMjhf
300-209 simos IS FAKE FAKE FAK
NEW QUESTION 496
Which two unified communications protocols can be inspected for an anomaly by using the Cisco ASA 5500 Series firewall? (Choose two.)
A. RSH
B. SCP
C. MGCP
D. TFTP
E. RTSP
Answer: CE
NEW QUESTION 497
Which purpose of MKA in a MACsec deployment is true?
A. It encrypts traffic between switches.
B. It transports EAP messages from access switches to the RADIUS server.
C. It provides additional security features beyond the default SAP key exchange.
D. It encrypts traffic between the downlink port and the endpoint of the switch.
Answer: D
NEW QUESTION 498
Due to a traffic storm on your network, two interfaces were error-disabled and both interfaces sent SNMP traps. In which two ways can the interfaces be back into service? (Choose two.)
A. If the snmp-server enable traps command is enabled, the ports return to service automatically after 300 seconds.
B. If EEM is configured, the ports return to service automatically in less than 300 seconds.
C. If the administrator enters the shutdown and no shutdown commands on the interfaces.
D. If the interfaces are configured with the error-disable detection and recovery feature, the interfaces will be returned to service automatically.
E. If Cisco Prime is configured, it issues an SNMP set command to re-enable the ports after the preconfigured interval.
Answer: CD
NEW QUESTION 499
You need to increase the level of security for the management traffic accessing a Cisco router. You plan to enable HTTPS. Which action do you take on the router?
A. Disable TCP port 23.
B. Generate an RSA key.
C. Enable SCP.
D. Enable TLS.
Answer: D
NEW QUESTION 500
Which action do you take on a Cisco router to limit the management traffic to only one interface?
A. Filter incoming connections by applying an extended ACL on a loopback interface.
B. Filter incwdoming connections by applying a standard ACL on a SVI.
C. Utilize the Management Plan Protection feature.
D. Add an interface by using the management-interface command.
Answer: C
NEW QUESTION 497
Which purpose of MKA in a MACsec deployment is true?
A. It encrypts traffic between switches.
B. It transports EAwdP messages from access switches to the RADIUS server.
C. It provides additional security features beyond the default SAP key exchange.
D. It encrypts traffic between the downlink port and the endpoint of the switch.
Answer: D
does anyone have the dumps for 300-210 exam ? would you be able to share it please ?
hi,
Maybe someone know, when I now pass simos 300-209 and next for example 2021 year I will pass new SCOR 300-701 exam (ccnp security core exam) but I don’t have CCNA Sec.
Than finally I get CCNP Sec cert ?
Hi Guys,
Does anyone have the steps to configure the Same SIM(bookmarks)?
Thanks in advance.
@Dani_Prime
look to this comment “@Dymos3 – January 26th, 2020”
Hi All
In “Bookmarks” Lap
Where can i find the (“Select Bookmark type” = “URL with GET or POST method” ) in ASDM ?
Thank you in advance.
Hi, question from 300-209:
Which three types of web resources or protocols are enabled by default on the Cisco ASA Clientless SSL VPN portal? (Choose three.)
A. HTTP
B. VNC
C. CIFS
D. RDP
E. HTTPS
F. ICA (Citrix)
Proposal answer is: ACE, but I think that correct answer should be: CDE (CIFS, RDP, HTTPS).
“By default, the ASA allows all portal traffic to all Web resources (for example HTTPS, CIFS, RDP, and plug-ins).”
https://www.cisco.com/c/en/us/td/docs/security/asa/asa94/config-guides/cli/vpn/asa-94-vpn-config/webvpn-configure-gateway.html
What do you think?
Another question about 300-209:
What represents a possible network configuration issue in clientless SSL VPN deployments?
A. The AnyConnect version is not up to date.
B. The VPN IP pool is exhausted.
C. The SSL server public certificate is untrusted.
D. NAT exemption has not been configured.
Answer is: C, but my question is that answer B is possible for clientless SSL VPN access?
300-209 wrong answer in Q from supermario:
An engineer is troubleshooting VPN connectivity issues between a PC and ASA using Cisco AnyConnect IPsec IKEv2.
Which requirement must be satisfied for proper functioning?
A. The SAN must be used as the CN for the ASA-side certificates.
B. Profile and binary updates must be downloaded over IPsec.
C. The connection must use EAP-AnyConnect.
D. PC certificate must contain the server-auth EKU.
Correct answer is: C
https://www.cisco.com/c/en/us/support/docs/security/anyconnect-secure-mobility-client/113692-technote-anyconnect-00.html
@ Wild_Wolf.
300-210 – This is everything I have and used for the exam. I passed the exam in early December with a 963 score.
od.lk/f/MzhfNjM2OTg2M18
ATTENTION PLEASE!
The new PassLeader 300-206 dumps (Updated Recently) now are available, here are part of 300-206 exam questions (FYI):
[Get the download link at the end of this post]
NEW QUESTION 492
Which two device types can you examine with a TrustSec Readiness Assessment report? (Choose two.)
A. SGACL devices
B. TrustSec incapable devices
C. enforcement devices
D. authentication devices
E. security group tagging devices
Answer: BC
NEW QUESTION 493
An engineer has found that threat detection has been turned on by default on a Cisco ASA. Which two security events are monitored? (Choose two.)
A. number of times the rates were exceeded
B. total number of malformed packets received
C. denial of service attack occurrences
D. packets allowed by the inspection engine
E. concurrent NAT interface overload addresses
Answer: AC
NEW QUESTION 494
Which two values must you provide when you use a CSV file to import devices into Cisco Prime Infrastructure? (Choose two.)
A. device model number
B. SNMP version
C. device serial number
D. device IP address
E. EtherType field
Answer: BD
NEW QUESTION 495
Which two features does DNSSEC leverage for proper functionality? (Choose two.)
A. It uses TCP to ensure reliable delivery.
B. It uses UDP to reduce the DNS responses time.
C. It uses EDNS to manage the larger DNS packets it requires.
D. It uses UDP to minimize packet size.
E. It uses AD and DO inside UDP to reduce response time.
Answer: CE
NEW QUESTION 496
Which two unified communications protocols can be inspected for an anomaly by using the Cisco ASA 5500 Series firewall? (Choose two.)
A. RSH
B. SCP
C. MGCP
D. TFTP
E. RTSP
Answer: CE
NEW QUESTION 497
Which purpose of MKA in a MACsec deployment is true?
A. It encrypts traffic between switches.
B. It transports EAP messages from access switches to the RADIUS server.
C. It provides additional security features beyond the default SAP key exchange.
D. It encrypts traffic between the downlink port and the endpoint of the switch.
Answer: D
NEW QUESTION 498
Due to a traffic storm on your network, two interfaces were error-disabled and both interfaces sent SNMP traps. In which two ways can the interfaces be back into service? (Choose two.)
A. If the snmp-server enable traps command is enabled, the ports return to service automatically after 300 seconds.
B. If EEM is configured, the ports return to service automatically in less than 300 seconds.
C. If the administrator enters the shutdown and no shutdown commands on the interfaces.
D. If the interfaces are configured with the error-disable detection and recovery feature, the interfaces will be returned to service automatically.
E. If Cisco Prime is configured, it issues an SNMP set command to re-enable the ports after the preconfigured interval.
Answer: CD
NEW QUESTION 499
You need to increase the level of security for the management traffic accessing a Cisco router. You plan to enable HTTPS. Which action do you take on the router?
A. Disable TCP port 23.
B. Generate an RSA key.
C. Enable SCP.
D. Enable TLS.
Answer: D
NEW QUESTION 500
Which action do you take on a Cisco router to limit the management traffic to only one interface?
A. Filter incoming connections by applying an extended ACL on a loopback interface.
B. Filter incoming connections by applying a standard ACL on a SVI.
C. Utilize the Management Plan Protection feature.
D. Add an interface by using the management-interface command.
Answer: C
NEW QUESTION 501
……
P.S.
PassLeader 300-206 dumps FYI:
od.lk/fl/NjFfMTUyNjc0M18
(501q~~~NEW VERSION DUMPS!!!)
Good Luck!!!
[(copy that link and open it in your web browser!!!)]
By the way:
1. PassLeader 300-208 dumps FYI:
od.lk/fl/NjFfMTUyNjc0NV8
(521q~~~NEW VERSION DUMPS!!!)
~~~~~~~~~~~~~~~~~~~~~~~~~
2. PassLeader 300-209 dumps FYI:
od.lk/fl/NjFfMTUyNjc0N18
(459q~~~NEW VERSION DUMPS!!!)
~~~~~~~~~~~~~~~~~~~~~~~~~
3. PassLeader 300-210 dumps FYI:
od.lk/fl/NjFfMTUyNjc0OV8
(508q~~~NEW VERSION DUMPS!!!)
~~~~~~~~~~~~~~~~~~~~~~~~~
Good Luck!!!
[(copy those links and open them in your web browser!!!)]
Hello people,
I passed exam 300-209 couple days ago. Bookmarks Lab was working, as mention in scenario all changes are automatically applied. Make sure to fallow instructions, enable on interface test, logut, configure bokmarks, apply test again. When you click on hyperlinks on portal http or ftp you should be redirected to to server
Had D&D packets send received, sanity check…
New DMVN – Make sure that you know all as mentioned, for example when it sends reply on port 500. This D&D is random it can start from NHRP request than go from phase MM3. I had like this
The NHRP Registration Request is then encapsulated in GRE which triggers the crypto process to start.
At this point, the first ISAKMP Main Mode message – ISAKMP MM1 – is sent from the Spoke to the Hub on port UDP500.
The Hub receives and processes MM1 and responds with ISAKMP MM2, as it has a matching ISAKMP policy.
Once the Spoke receives the MM2, it responds with MM3. As with MM1, the Spoke confirms the received ISAKMP policy is valid.
The Hub receives MM3 and responds with MM4.
At this point in the ISAKMP negotiation, the Spoke might respond on port UDP4500 if NAT is detected in the transit path. However, if no NAT is detected the Spoke continues and sends MM5 on UDP500.
Hub responds with MM6 in order to complete the Main Mode .
crypto session is up and able to pass traffic, these packets are encapsulated within the GRE over IPSec tunnel
I hope you are getting idea
*apply test again =assign policy and test again
@hi what do you mean test ? can you please be clear on the bookmarks lab
Another wrong answer in supermario Q…
Refer to the exhibit. A NOC engineer needs to tune some postlogin parameters on an SSL VPN tunnel.
[cut screen]
From the information shown, where should the engineer navigate to, in order to find all the postlogin session parameters?
A. “engineering” Group Policy
B. “contractor” Connection Profile
C. DefaultWEBVPNGroup Group Policy
D. DefaultRAGroup Group Policy
E. “engineer1” AAA/Local Users
Correct answer is: A.
@Angelo, Thank very much! I am going to have a look ;)
I passed today 300-209 and I’ll give you the same tips as “Passed today” said above:
1. Please don’t panic
2. Supermario still enough to make you pass
3. With regarding to the lab (Bookmark) I did everything but I was unable to see the bookmarks on the client and I’ve logout a couple times, but I believe
4. DMVPN eight steps if you go through Wild_Wolf steps then you should be alright..
Testing in the morning. Cautiously Optimistic.
Taking the exam on saturday @ DB1 please advise how did you go thanks
Which bookmark lab is on the exam 300-209 the one with wizard or the one without it
Hi all,
Please confirm the DMVPN eight steps. i am try to attempt coming Monday
Thanks
Is the below question correct?
QUESTION 225
Which three changes must be made to migrate from DMVPN Phase 2 to Phase 3 when EIGRP is configured? (Choose three.)
A. Enable EIGRP next-hop-self on the hub.
B. Disable EIGRP next-hop-self on the hub.
C. Enable EIGRP split-horizon on the hub.
D. Add NHRP redirects on the hub.
E. Add NHRP shortcuts on the spoke. F. Add NHRP shortcuts on the hub.
Correct Answer: BDE
Thanks ;)
Hi,
can any one share with correct answers of eight DMVPN steps.
friends,
I have a summary of the exam 210-260, 300-206, 300-208, 300-209 and 300-210.
You only need these files to pass 100% confirmed.
Many know me, if you are interested please write to the following email.
ccnpswicth@ gmail. com*
Well I passed this morning. 912/1000
LAB: Bookmarks.
I had the no shortcuts issue in the Bookmarks lab and I’m sure that hurt my score. I checked, double checked, and triple checked every every setting. Did everything just as the lab showed and still no bookmarks showed up in the PC.
Anyway………57 questions. ALL QUESTIONS ARE EITHER IN SUPERMARIO V4 OR ON THE LAST FEW PAGES OF THIS FORUM (See Free’s post on Dec 24th)
SIMLET – ikev2 l2l questions ( sh cryp isa key, sh cry isa sa, sh cry ipsec trans )
D/D
Ikev1 troubleshooting ( attr, qm_idle…etc)
DMVPN – You must know all 11 steps (My exam had steps 2 thru 8)
1. When the Tunnel on the Spoke is “no shutdown” it generates a NHRP Registration Request, which starts the DMVPN process. As the Hub’s configuration is completely dynamic, the Spoke must be the endpoint which initiates the connection.
2. The NHRP Registration Request is then encapsulated in GRE which triggers the crypto process to start.
3. At this point, the first ISAKMP Main Mode message – ISAKMP MM1 – is sent from the Spoke to the Hub on port UDP500.
4. The Hub receives and processes MM1 and responds with ISAKMP MM2, as it has a matching ISAKMP policy.
5. Once the Spoke receives the MM2, it responds with MM3. As with MM1, the Spoke confirms the received ISAKMP policy is valid.
6. The Hub receives MM3 and responds with MM4.
7. At this point in the ISAKMP negotiation, the Spoke might respond on port UDP4500 if NAT is detected in the transit path. However, if no NAT is detected the Spoke continues and sends MM5 on UDP500. Lastly, the Hub responds with MM6 in order to complete the Main Mode exchange.
8. Once the Spoke receives MM6 from the Hub, it sends QM1 to the Hub on UDP500 in order to begin Quick Mode.
9. The Hub receives QM1 and responds with QM2, as all received attributes are accepted. At this point the Hub creates the Phase 2 SAs for this session.
10. As the last step of the Quick Mode negotiation, QM2 is received by the Spoke. The Spoke then creates its Phase 2 SAs and sends QM3 in response. This completes the ISAKMP and IPSec negotiation. There is now an IPSec session which encrypts GRE traffic between these two peers.
11. Now that the crypto session is up and able to pass traffic, these packets are encapsulated within the GRE over IPSec tunnel
I have now completed my CCNP Security.
Passed today with 964/1000.
Labs -> SIM & check config to answer
D&D -> portals
Good luck to all
Copy link and paste in your browser
poweredbydialup.online/WV4VYT
QUESTION 225
Which three changes must be made to migrate from DMVPN Phase 2 to Phase 3 when EIGRP is configured? (Choose three.)
A. Enable EIGRP next-hop-self on the hub.
B. Disable EIGRP next-hop-self on the hub.
C. Enable EIGRP split-horizon on the hub.
D. Add NHRP redirects on the hub.
E. Add NHRP shortcuts on the spoke. F. Add NHRP shortcuts on the hub.
Correct Answer: BDE…
hi all,
just passed the exam (9xx) some hours before.
supermario is still perfectly valid + plus some new questions which is already mention here.
SSL lab was Perfect with no issues. i test both the bookmarks which open a webpage(HTTP) and ftp director(FTP) after completion.
about the new 8 steps D&D follow @WILD WOLF steps.
but in the exam there was a separate step “SPOKE VALIDATE ISAKMP POLICY”
i think this would confuse exam takers.
i keep this step at “STEP # 4”
D&D has only Main Mode 8 steps. No Quick Mode Steps.
the last step would be “the Hub responds with MM6 in order to complete the Main Mode exchange”.
hope you wud got idea.
regards,
@ Octopus
A should be the correct one.
Hi All,
I am looking for stable 300-208 dumps. If someone need 300-210 exam I have a very short version of questions only 100 questions many people already passed the exam.
Please share your experience nikolai112….@аbv.bg Remove ….
Thank you very much in advance!
I have valid SPOTO 300-209 and 200-210 dumps.
If anyone is interested I can share only for 50 dollars or will give some discount so that everyone can reach the destination before 24th Feb 2020.
(300-209 Reviews, Remove spaces)
https: // drive.google.com/drive/folders/1ZEwzqwWXwz2z7w70b9u2564y9g5b7qD2?usp=sharing
(300-210 Reviews, Remove spaces)
https: // drive.google.com/drive/folders/1wQj_aHRQXg1Ifm3ExMn_L5AXUr9dw0wv?usp=sharing
My whatssapp +92-346-5363766
Correction. (300-209 and 300-210)
I have valid SPOTO 300-209 and 300-210 dumps.
If anyone is interested I can share only for 50 dollars or will give some discount so that everyone can reach the destination before 24th Feb 2020.
(300-209 Reviews, Remove spaces)
https: // drive.google.com/drive/folders/1ZEwzqwWXwz2z7w70b9u2564y9g5b7qD2?usp=sharing
(300-210 Reviews, Remove spaces)
https: // drive.google.com/drive/folders/1wQj_aHRQXg1Ifm3ExMn_L5AXUr9dw0wv?usp=sharing
My whatssapp +92-346-5363766
Islamabad-Rohail IS FAKE FAKE FAKE FAKE
Islamabad-Rohail IS FAKE FAKE FAKE FAKE…
Is this question correct?
When you are configuring a hub-and-spoke DMVPN network, which tunnel mode should you use
for the spoke router configuration?
A. GRE multipoint
B. Classis point-to-point GRE
C. IPsec multipoint
D. Nonbroadcast multiaccess
Answer: A
Thanks!
@DB1: Thanks buddy
I am just a student like you. Just want to recover my amount which I paid for the dumps.
I do not force anyone to buy only from me. Thank you
Hi All,
Apart from the below D&D question, do you know if there is more D&D question?
1. When the Tunnel on the Spoke is “no shutdown” it generates a NHRP Registration Request, which starts the DMVPN process. As the Hub’s configuration is completely dynamic, the Spoke must be the endpoint which initiates the connection.
2. The NHRP Registration Request is then encapsulated in GRE which triggers the crypto process to start.
3. At this point, the first ISAKMP Main Mode message – ISAKMP MM1 – is sent from the Spoke to the Hub on port UDP500.
4. The Hub receives and processes MM1 and responds with ISAKMP MM2, as it has a matching ISAKMP policy.
5. Once the Spoke receives the MM2, it responds with MM3. As with MM1, the Spoke confirms the received ISAKMP policy is valid.
6. The Hub receives MM3 and responds with MM4.
7. At this point in the ISAKMP negotiation, the Spoke might respond on port UDP4500 if NAT is detected in the transit path. However, if no NAT is detected the Spoke continues and sends MM5 on UDP500. Lastly, the Hub responds with MM6 in order to complete the Main Mode exchange.
8. Once the Spoke receives MM6 from the Hub, it sends QM1 to the Hub on UDP500 in order to begin Quick Mode.
9. The Hub receives QM1 and responds with QM2, as all received attributes are accepted. At this point the Hub creates the Phase 2 SAs for this session.
10. As the last step of the Quick Mode negotiation, QM2 is received by the Spoke. The Spoke then creates its Phase 2 SAs and sends QM3 in response. This completes the ISAKMP and IPSec negotiation. There is now an IPSec session which encrypts GRE traffic between these two peers.
11. Now that the crypto session is up and able to pass traffic, these packets are encapsulated within the GRE over IPSec tunnel
A guy from texas just passed 300-209 exam today.
Please find his review in below URL. Remove spaces.
(300-209 Reviews, Remove spaces)
https: // drive.google.com/drive/folders/11JJ-6LW-ZJ_5wZpF13mtK1ip2wattpRR?usp=sharing
(300-210 Reviews, Remove spaces)
https: // drive.google.com/drive/folders/1wQj_aHRQXg1Ifm3ExMn_L5AXUr9dw0wv?usp=sharing
If anyone is interested I can share only for 50 dollars or will give some discount so that everyone can reach the destination before 24th Feb 2020.
My whatssapp +92-346-5363766
Hi All,
I am requesting you to, please share New questions and answer which was you got in your exam.
Thanks.
Can someone please link a free VCE player? Thanks!
Test is tomorrow and I will report back.
Good luck Dylan!! Please give us an update and if possible remember some of the new questions!! Thanks in advance…
@Danny
I appreciate the kind words and I’ll be sure to bring back some information.
Hola, everybody here!
The new PassLeader 300-206 dumps (Updated Recently) now are available, here are part of 300-206 exam questions (FYI):
[Get the download link at the end of this post]
NEW QUESTION 481
An engineer wants to ensure that a multicontext Cisco ASA determines the proper context to send a packet. Which two classification criteria must be unique for each context for this determination to occur? (Choose two.)
A. ARP table
B. transparent forwarding
C. session state
D. interfaces
E. MAC addresses
Answer: DE
NEW QUESTION 482
Which two device types can you examine with a TrustSec Readiness Assessment report? (Choose two.)
A. SGACL devices
B. TrustSec incapable devices
C. enforcement devices
D. authentication devices
E. security group tagging devices
Answer: BC
NEW QUESTION 483
An engineer has found that threat detection has been turned on by default on a Cisco ASA. Which two security events are monitored? (Choose two.)
A. number of times the rates were exceeded
B. total number of malformed packets received
C. denial of service attack occurrences
D. packets allowed by the inspection engine
E. concurrent NAT interface overload addresses
Answer: AC
NEW QUESTION 484
Which two values must you provide when you use a CSV file to import devices into Cisco Prime Infrastructure? (Choose two.)
A. device model number
B. SNMP version
C. device serial number
D. device IP address
E. EtherType field
Answer: BD
NEW QUESTION 485
Which two features does DNSSEC leverage for proper functionality? (Choose two.)
A. It uses TCP to ensure reliable delivery.
B. It uses UDP to reduce the DNS responses time.
C. It uses EDNS to manage the larger DNS packets it requires.
D. It uses UDP to minimize packet size.
E. It uses AD and DO inside UDP to reduce response time.
Answer: CE
NEW QUESTION 486
Which two unified communications protocols can be inspected for an anomaly by using the Cisco ASA 5500 Series firewall? (Choose two.)
A. RSH
B. SCP
C. MGCP
D. TFTP
E. RTSP
Answer: CE
NEW QUESTION 487
Which purpose of MKA in a MACsec deployment is true?
A. It encrypts traffic between switches.
B. It transports EAP messages from access switches to the RADIUS server.
C. It provides additional security features beyond the default SAP key exchange.
D. It encrypts traffic between the downlink port and the endpoint of the switch.
Answer: D
NEW QUESTION 488
Due to a traffic storm on your network, two interfaces were error-disabled and both interfaces sent SNMP traps. In which two ways can the interfaces be back into service? (Choose two.)
A. If the snmp-server enable traps command is enabled, the ports return to service automatically after 300 seconds.
B. If EEM is configured, the ports return to service automatically in less than 300 seconds.
C. If the administrator enters the shutdown and no shutdown commands on the interfaces.
D. If the interfaces are configured with the error-disable detection and recovery feature, the interfaces will be returned to service automatically.
E. If Cisco Prime is configured, it issues an SNMP set command to re-enable the ports after the preconfigured interval.
Answer: CD
NEW QUESTION 489
You need to increase the level of security for the management traffic accessing a Cisco router. You plan to enable HTTPS. Which action do you take on the router?
A. Disable TCP port 23.
B. Generate an RSA key.
C. Enable SCP.
D. Enable TLS.
Answer: D
NEW QUESTION 490
Which action do you take on a Cisco router to limit the management traffic to only one interface?
A. Filter incoming connections by applying an extended ACL on a loopback interface.
B. Filter incoming connections by applying a standard ACL on a SVI.
C. Utilize the Management Plan Protection feature.
D. Add an interface by using the management-interface command.
Answer: C
NEW QUESTION 491
……
P.S.
PassLeader 300-206 dumps FYI:
od.lk/fl/NjFfMTUyNjc0M18
(494q~~~NEW VERSION DUMPS!!!)
Good Luck!!!
[(copy that link and open it in your web browser!!!)]
By the way:
1. PassLeader 300-208 dumps FYI:
od.lk/fl/NjFfMTUyNjc0NV8
(521q~~~NEW VERSION DUMPS!!!)
~~~~~~~~~~~~~~~~~~~~~~~~~
2. PassLeader 300-209 dumps FYI:
od.lk/fl/NjFfMTUyNjc0N18
(459q~~~NEW VERSION DUMPS!!!)
~~~~~~~~~~~~~~~~~~~~~~~~~
3. PassLeader 300-210 dumps FYI:
od.lk/fl/NjFfMTUyNjc0OV8
(499q~~~NEW VERSION DUMPS!!!)
~~~~~~~~~~~~~~~~~~~~~~~~~
Good Luck!!!
[(copy those links and open them in your web browser!!!)]
Hi!
Congratulations!
Took the 300-209 exam few days ago and passed it with 920 points!
Got totally 57 questions, ALL QUESTIONS ARE IN PassLeader 300-209 dumps.
Bookmarks Lab (got no shortcuts issue in it…sadly to say) and DMVPN (is random it can start from NHRP request than go from phase MM3).
All in all, thanks PassLeader 300-209 dumps, it helped a lot for my passing!
Good luck!
Passed today with 964!
Labs -> SIM & check config to answer
D&D -> portals
Good luck to all
Copy link and paste in your browser
poweredbydialup.online/WV4VY
NEW QUESTION 488
Due to a traffic storm on your network, two interfaces were error-disabled and both interfaces sent SNMP traps. In which two ways can the interfaces be back into service? (Choose two.)
A. If the snmp-server enable traps command is enabled, the ports return to service automatically after 300 seconds.
B. If EEM is configured, the ports return to service automatically in less than 300 seconds.
C. If the administrator enters thuye shutdown and no shutdown commands on the interfaces.
D. If the interfaces are configured with the error-disable detection and recovery feature, the interfaces will be returned to service automatically.
E. If Cisco Prime is configured, it issues an SNMP set command to re-enable the ports after the preconfigured interval.
Answer: CD….
Anonymous, do you have a document with 448 questions on it? could you please share it with me?
In addition, which is the D&D (portals) question? I only have the DMVPN and debug messages D&D questions.
Thanks in advance.
Hey guys,
Just passed the exam (9xx) with no problem at all.
supermario is still perfectly valid + plus some new questions which were already mentioned here.
SSL lab was Perfect with no issues. Just make sure to apply your changes, and logout of the Clientless SSL VPN on the Gues-PC before testing the bookmarks.
ASDM (VPN command – show crypto isakmp key, show crypto ipsec sa and show crypto isakmp sa).
D&D follow @WILD WOLF steps.
Good luck everyone!
Hi all
Can anyone help me and explain the question number 445 in supermario Dump ?
it is a D&D question.
Thank you in advance.
Hi Dylan,
Can you help us in the 11 step what is the question and what is the answer. please.
1. When the Tunnel on the Spoke is “no shutdown” it generates a NHRP Registration Request, which starts the DMVPN process. As the Hub’s configuration is completely dynamic, the Spoke must be the endpoint which initiates the connection.
2. The NHRP Registration Request is then encapsulated in GRE which triggers the crypto process to start.
3. At this point, the first ISAKMP Main Mode message – ISAKMP MM1 – is sent from the Spoke to the Hub on port UDP500.
4. The Hub receives and processes MM1 and responds with ISAKMP MM2, as it has a matching ISAKMP policy.
5. Once the Spoke receives the MM2, it responds with MM3. As with MM1, the Spoke confirms the received ISAKMP policy is valid.
6. The Hub receives MM3 and responds with MM4.
7. At this point in the ISAKMP negotiation, the Spoke might respond on port UDP4500 if NAT is detected in the transit path. However, if no NAT is detected the Spoke continues and sends MM5 on UDP500. Lastly, the Hub responds with MM6 in order to complete the Main Mode exchange.
8. Once the Spoke receives MM6 from the Hub, it sends QM1 to the Hub on UDP500 in order to begin Quick Mode.
9. The Hub receives QM1 and responds with QM2, as all received attributes are accepted. At this point the Hub creates the Phase 2 SAs for this session.
10. As the last step of the Quick Mode negotiation, QM2 is received by the Spoke. The Spoke then creates its Phase 2 SAs and sends QM3 in response. This completes the ISAKMP and IPSec negotiation. There is now an IPSec session which encrypts GRE traffic between these two peers.
11. Now that the crypto session is up and able to pass traffic, these packets are encapsulated within the GRE over IPSec tunnel
I am confused with the following question. Solutions say Cisco Unified communications is the correct answer, but it doesn’t make much sense.
Could someone confirm?
On which type of encrypted traffic can a Cisco ASA appliance running software version 8.4.1 perform application inspection and control?
IPsec
SSL
IPsec or SSL
Cisco unified Communications
Secure FTP
My contribution to the community.
D&D from the test with the order which I think is correct.
The ISAKMP MM1 main mode message is sent from the spoke to the hub using the default IKE port.
The hub processes received MM1 and replies with an appropriate ISAKMP policy MM2 message.
The spoke receives an MM2 message, sends an MM3.
The hub receives MM3 and replies by sending MM4.
The spoke replies on port UDP4500 if NAT is detected in the transit path or UDP500 when NAT-T is not detected.
The hub replies by sending MM6, which completes the main mode exchange.
The spoke validates the received ISAKMP policy.
The NHRP Registration Request is encapsulated in GRE.
D&D from the test with the order which I think is correct.
The ISAKMP MM1 main mode message is sent from the spoke to the hub using the default IKE port.
The hub processes received MM1 and replies with an appropriate ISAKMP policy MM2 message.
The spoke receives an MM2 message, sends an MM3.
The hub receives MM3 and replies by sending MM4.
The spoke replies on port UDP4500 if NAT is detected in the transit path or UDP500 when NAT-T is not detected.
The hub replies by sending MM6, which completes the main mode exchange.
The spoke validates the received ISAKMP policy.
The NHRP Registration Request is encapsulated in GRE. – this is step 2, shouldn’t be placed in the beginning?
Rob
You are right. That is step one. My mistake.